Announcement
Collapse
No announcement yet.
FC 13BT rebuild to 3mm or not to 3mm
Collapse
X
-
the seals are actually really nice, just the springs wear out so if you can get just the RA seals w/o the springs and order some stock mazda apex seal springs then go for it.
-
Originally posted by theflatlanderyeah about the RA kit, i've heard a lot of problems with the apex seal springs flattening out real early, but if you use stock mazda springs it shouldnt be a problem.
Thanks for the info. I hadn't heard what about the RA seals was going bad. I knew that their seals were supposed to be great. So just use the stock Mazda seals then? I have a friend who just ordered a set too. I'll be sure to let him know.
Zach
Leave a comment:
-
Originally posted by BoostedrexTrots,
The Mazda rebuild kit is fine. So is the Atkins kit though. I like Rotary Aviation, but I have had a few friends who have had trouble with their apex seals. Get with mazdatrix to get a rebuild kit if you don't feel like going with Atkins. About the EMS issue. You can run on a streetport with the stock EMS. I wouldn't recommend it. You can pick up a used Apex'i SAFC for $200. That would take care of your fuel needs until you could afford a nice Haltech or Microtech. I ran my FC for about a year with a HUGE streetport and I used the SAFC. I was running a Walbro 255 fuel pump, stock primary injectors, and 720cc secondaries. I never had any problems. Could boost up to 14psi. I'm very glad that I switched to a Haltech now though. Like always, let me know if I can be of any help.
Zach
Leave a comment:
-
Trots,
The Mazda rebuild kit is fine. So is the Atkins kit though. I like Rotary Aviation, but I have had a few friends who have had trouble with their apex seals. Get with mazdatrix to get a rebuild kit if you don't feel like going with Atkins. About the EMS issue. You can run on a streetport with the stock EMS. I wouldn't recommend it. You can pick up a used Apex'i SAFC for $200. That would take care of your fuel needs until you could afford a nice Haltech or Microtech. I ran my FC for about a year with a HUGE streetport and I used the SAFC. I was running a Walbro 255 fuel pump, stock primary injectors, and 720cc secondaries. I never had any problems. Could boost up to 14psi. I'm very glad that I switched to a Haltech now though. Like always, let me know if I can be of any help.
Zach
Leave a comment:
-
Originally posted by Trots*88TII-AE*Thanks a lot man, that info really helps me out. I was planning on staying pretty conservative with the power, i'm on a tyte budget so probably stock turbo for now and definately gonna be under 300 hp. Would i be able to get by on stock ECU with a piggy back if i port it, or will i still need a full EMS? and, are the factory Mazda rebuild kits w/ 2 piece 2mm seals the best kits to buy? or are the aftermarket kits better??
Leave a comment:
-
Originally posted by BoostedrexTrots,
Everybody hit the nail on the head about the apex seals. 3mm seals are nothing more than a crutch that allow poor tuning. 2mm 2 piece seals will be more than adequate.
As for porting your engine, a street port will not shorten the life span of your engine. You won't lose much bottom end if you even lose any. Both of my 7's have streetports. The FD has a mild port and the TII has huge streetports. Both of them are very civilized on the street and niether one has any lack of bottom end power. If you need a good shop then check out Judge Ito, Bryan Cain, Rotor Sports Racing, Pinneaple, KD Rotary, and/or Atkins rotary. And I would suggest checking them out in that order. As for the stand alone EMS, you need it if you are planning on going with big power. Anything at or over 300rwhp I would strongly suggest a stand alone. Check out the Haltech E6X or the Microtec setups. I don't have any experience with Microtec so I can't say good or bad about them. I have heard good things about that company though. I do have experience with Haltech so I would say go with them. They make a great product and they have pretty good prices depending on who you buy it from. As always, if you have any questions please feel free to PM me or email me at boostedrex@gmail.com
Vosko!!!!!!! Good to see you posting on here bro. How's the S13 doing? Missing rotaries much yet? Take care!
Zach
Leave a comment:
-
Trots,
Everybody hit the nail on the head about the apex seals. 3mm seals are nothing more than a crutch that allow poor tuning. 2mm 2 piece seals will be more than adequate.
As for porting your engine, a street port will not shorten the life span of your engine. You won't lose much bottom end if you even lose any. Both of my 7's have streetports. The FD has a mild port and the TII has huge streetports. Both of them are very civilized on the street and niether one has any lack of bottom end power. If you need a good shop then check out Judge Ito, Bryan Cain, Rotor Sports Racing, Pinneaple, KD Rotary, and/or Atkins rotary. And I would suggest checking them out in that order. As for the stand alone EMS, you need it if you are planning on going with big power. Anything at or over 300rwhp I would strongly suggest a stand alone. Check out the Haltech E6X or the Microtec setups. I don't have any experience with Microtec so I can't say good or bad about them. I have heard good things about that company though. I do have experience with Haltech so I would say go with them. They make a great product and they have pretty good prices depending on who you buy it from. As always, if you have any questions please feel free to PM me or email me at boostedrex@gmail.com
Vosko!!!!!!! Good to see you posting on here bro. How's the S13 doing? Missing rotaries much yet? Take care!
Zach
Leave a comment:
-
Power gain depends on port timing, tuning and how much boost you'll be running, and a mild street port isn't gonna decrease engine life at all, and pending on what size turbo your gonna run your bottom end will be just as good if not better.
Leave a comment:
-
it all depends on who dose the porting. different shops do different porting. I have seen "street ports" done by certain shops that are much smaller then other shops "street ports"
I would recomend running a stand alone, especialy if you go with one of those bigger street ports.
Leave a comment:
-
what kind of power gains can you get from mild streetporting? and do you lose considerable bottom end by doing it or reduce your engine life?
Leave a comment:
-
are you guys running standalones? i havent ported mine yet(havent rebuild mine yet) but after i do a street port, i plan to use a microtech ems(any comments are welcome or experience on the ltx12s)
Leave a comment:
-
how big are your bridges? And i was mostly talking about j-bridges and bridged turbo motors. Also can i see some pics of your rx-2?, gotta love old school.Last edited by theflatlander; 02-09-2005, 08:06 PM.
Leave a comment:
-
my RX2 has a 13B bridge ported, 48 IDA webber and extractors
i've never had any probs with its since it was ported
Leave a comment:
-
Originally posted by S13/R32get it bridge ported or j ported
bridge porting has a nice sound
j ports are kinda loud and are probly better for fuel injected cars i think bridge is more for carby rotors but i could be wrong im more of a pistons guy
Leave a comment:
-
I have always run 2mm seals in my race motors, but make sure you go with a 2mm, 2 piece apex seal. all the mazda remans now come with a 2 piece seals instead of the original 3 piece.
Leave a comment:
Leave a comment: