ad

Announcement

Collapse
No announcement yet.

ENGINE TUNING DVD SERIES (Vol.1) by DRIFTING.com

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • ENGINE TUNING DVD SERIES (Vol.1) by DRIFTING.com

    <iframe width="640" height="480" src="//www.youtube.com/embed/u5LgJMuqEaM" frameborder="0" allowfullscreen></iframe>
    DVD ORDER PAGE - Engine Tuning Vol. 1[/B]
    http://store.driftingshop.com/pentudvdaplp.html

  • #2
    Nice!!!! I like it!!

    Comment


    • #3
      question

      Is this with a SR engine or KA24DET?

      I'd imagine you guys go into some of the math behind duty cycle ect so people with either engine can learn from this?

      Very interested in this DVD, is it exclusive to drifting.com?

      Comment


      • #4
        Originally posted by walperstyle View Post
        Is this with a SR engine or KA24DET?

        I'd imagine you guys go into some of the math behind duty cycle ect so people with either engine can learn from this?

        Very interested in this DVD, is it exclusive to drifting.com?

        The main focus of the first DVD in the Engine Tuning Series is to show how to setup and operate the software.

        Drifting.com is currently the only company that is authorized to sell this DVD.

        thank you

        Comment


        • #5
          When will this DVD be released?

          Comment


          • #6
            Originally posted by Reactor View Post
            When will this DVD be released?
            we have been sitting on the raw content for a few months but we need to re-film the dyno section with a video capture.

            the re-filming schedule has not been locked down, we might know more within 1-2 weeks

            Comment


            • #7
              we have been getting several emails and calls about this DVD so we will do our best to post updates on this thread


              -we plan to re-film near the end of July
              -the new version will been done with a video capture so the resolution is clearer

              The outline is done but more topics will be added after we apply the suggestions that have been submitted to us.

              Comment


              • #8
                we are restating the objective again because this is asked a lot...

                Vol. #1 will focus on how to operate the basic functions of the AEM EMS Software on the dyno

                Comment


                • #9
                  Any updates? Release date?

                  Comment


                  • #10
                    Originally posted by Reactor View Post
                    Any updates? Release date?
                    the content that we have can not be released

                    we are refilming within 1 or 2 hosts by either Sep-Oct or starting in January.

                    Comment


                    • #11
                      Originally posted by Reactor View Post
                      Any updates? Release date?
                      new update,
                      we might be able to lock this down by September, we will know more by tomorrow

                      Comment


                      • #12
                        Submitted Suggestions; By nutz @ SRT Forums

                        Opening the software
                        Loading a base map (always start with AEM’s base)
                        Setting up correct sensors for application
                        Setting up injectors and fuel pressure

                        Connecting to the ECU (can be difficult with obd-serial port)
                        Uploading your map
                        Setting the o2 gain (so gauge reads the same as the EMS sees)
                        THE START UP (yea now were getting some where)
                        Adjusting start up/warm up parameters
                        Getting it to idle (just for basic tuning)
                        Double check your timing/fuel maps (changes in sensors might make the map dangerous!!!)
                        How to do baseline (non-boost) VE mapping for A/F (low load)

                        (boost comp theory) predicting A/F load cells
                        How to set up and interpret logs (very very important)

                        Setting up o2 feed back
                        Tuning load A/F

                        Ignition timing tuning (dangerous subject)

                        Knock sensor setup
                        Setting up sensitivity for false knock
                        How much to pull/add and how quick

                        Putting it all together for drivability
                        Throttle fuel correction
                        Final idle adjustments
                        Rev limiters/2 step
                        Fan on –off


                        ADVANCED
                        Anti-lag theory and how to safely use it
                        Traction control ????????
                        Injector phase theory and how to (changes for boost comp and cams)
                        Staged injectors theory
                        How to set up inputs/outputs

                        Comment


                        • #13
                          We are schedule to re-film next weekend

                          Comment


                          • #14
                            Re-filming takes place tomorrow

                            Comment


                            • #15
                              over 3 hours of usable content was captured today

                              Comment

                              Working...
                              X